scooters Maintenance
scooter maintenance is pretty important. It’s even more important than on a car because the moped engine has to work harder and component failure can more easily lead to loss of control.
Perhaps the most important and easiest item of mopeds maintenance is to regularly check the oil level and change the oil at frequent intervals. We suggest changing the oil at least every 1000 miles is a good idea. The gas scooter oil capacity is less than 1 liter and so an oil change costs about $3 and takes about 5 minutes. It’s cheap insurance to keep your gas scooters engine running for as long as possible. Most of the manual recommends changing the gas moped transmission oil every 2000 miles or 6 months. Since it only takes about 100ml of oil (which costs under $1) and takes a couple of minutes to do, don’t skimp on gas mopeds transmission oil changes. We recommend using Castrol 10-30W engine oil and Castrol 80/90 transmission gear oil. Which scooter for sale oil you use is less important than how often you change it, though you probably should avoid using pure synthetic oil in a scooters for sale, especially during the break moped for sale in period. Once you have several thousand miles on the engine, a synthetic blend may be OK, but you should still change the oil regularly.
Checking mopeds for sale tire pressure regularly is also very important. Unlike a car, a chinese scooter only has two wheels and tire problems can lead more easily to a loss of control and possible injury, so making sure your chinese scooters tire pressures are correct makes sense.
Though a standard chinese moped maintenance schedule calls for checking bolt tightness every 1000 miles or 6 months, it certainly doesn’t hurt to do it more frequently.
Every 250 miles or every month:
Check scooters engine oil level
Check chinese mopeds tire pressure
Check cheap scooter lights and horn
Check cheap scooters battery level Every 1000 miles or every 6 months
Change engine oil
Check cheap moped tires for wear
Check valve stems for splits or cracks
Check cheap mopeds brakes and throttle operation. Lubricate cables if required
Check all screws nuts and bolts and tighten. Especially check muffler and exhaust fasteners and front and rear axles
Every 2000 miles or every year
Change the motor bike transmission oil
Check and adjust motor bikes valve clearance
Clean gas motor bike air cleaner
Check and clean (or replace) spark plug
Check gas motor bikes brake linings.
Check/clean/lubricate motor bike for sale brake and throttle cables.
Check motor bikes for sale CVT drive belt for wear and cracks
Check wheel and steering bearings
Though not exactly maintenance, We’d recommend carrying a basic tool kit at all times. That would include the following items:
3/8″ drive metric socket set
Flat blade and Phillips head screwdrivers
Roll of electrical tape
Roll of duct tape
Pair of pliers
Pair or wire cutters
Flashlight (LED type for long battery life)
Short length of wire
Set of metric wrenches
Short length of fuel/vacuum hose
Spark plug wrench and spare spark plug
A few nylon cable ties
chinese motor bike Brake-In
Different manufacturers recommend different break in procedures. For example most of our cheap motor bikes manufacturers recommend the following:
0-150km maximum speed 30km/hr
151-300km maximum speed 40km/hr
301-800km maximum speed 50km/hr
801-1500km maximum speed 60km/hr
Of course the speedometer is calibrated in mph and the odometer reads in miles, so some translation is needed. In round numbers these instructions correspond to:
0-100 miles maximum speed 20 mph
101-200 miles maximum speed 25 mph
201-500 miles maximum speed 30 mph
501-1000 miles maximum speed 40 mph
What we recommend is to use the “ride it like you’ll ride it (but gently)” technique. That involves riding pretty gently for the first 25 miles (speed under 30 mph, revs under 4000 rpm), then changing the original Chinese engine and transmission oil. The original oil might be OK or it might be “cheap and nasty”. You have no real way of telling, so change it, then you’ll be sure. You may replace the original oils with Castrol GTX 10-30W in the engine and Castrol Hypoid 80/90 gear oil in the chinese motor bikes transmission. For the next 175 miles (25-200) you still should take it quite easy with no rapid acceleration, keeping the speed down below 40mph or 5000 rpm, then go ahead change the engine oil again. Since there is no real oil filter (the “filter” is just a mesh screen), changing the oil during the break-in period makes sense since it removes small metal particulates that the filter just won’t catch.
During the break in period try to vary the engine speed as much as possible. This isn’t particularly easy with a CVT scooter since they tend to try to keep the revs pretty constant and change speed by changing the gear ratio. It is good to speed up and slow down and not ride at a constant throttle setting for long periods. Also avoid rapid starts and let the engine warm up for about a minute before moving off when you first start the cheap motor bike from cold to allow the oil to circulate. This is good advice even after the initial break-in period too.
It’s probably not a good idea to use synthetic oil during the break in period. Good old dino (dinosaur!) oil is probably what you should use. Synthetic oil may be too slippery and not allow the parts (mainly the piston rings) to “bed in” properly. We suggest to stick with the manufacturer’s recommendation (typically 10-30W) until after the break in period of 500-1000 miles. Then you can switch to a synthetic blend if you want to. Amsoil make a synthetic oil which they claim is specially designed for scooters.
Our break-in technique is to gradually increase speed over the next 300 miles (201-500) and at 500 miles do another oil change. After break-in, the engine oil should be changed at least every 1000 miles as part of normal routine maintenance.